Damage prediction in L-bending processes using FEMHAMBLI, Ridha; MKADDEM, Ali; POTIRON, Alain et al.International journal, advanced manufacturing technology. 2003, Vol 22, Num 1-2, pp 12-19, issn 0268-3768, 8 p.Article

Recent trends in numerical simulation of three-dimensional sheet forming processesYANG, D. Y; KIM, T. J; YOON, S. J et al.Proceedings of the Institution of Mechanical Engineers. Part B. Journal of engineering manufacture. 2003, Vol 217, Num 11, pp 1553-1570, issn 0954-4054, 18 p.Article

Robustness of the sheet metal springback cup testFOECKE, T; GNAEUPEL-HEROLD, T.Metallurgical and materials transactions. A, Physical metallurgy and materials science. 2006, Vol 37, Num 12, pp 3503-3510, issn 1073-5623, 8 p.Article

Reduction of springback using simultaneous stretch-bending processes : AMPTSCHILP, Hansjorg; SUH, Joungsik; HOFFMANN, Hartmut et al.International journal of material forming. 2012, Vol 5, Num 2, pp 175-180, issn 1960-6206, 6 p.Article

Air bending of AZ31 magnesium alloy sheetsPAISARN, Ratchanee; YUGI, Nobumasa; KOGA, Nobuhiro et al.Keikinzoku. 2005, Vol 55, Num 4, pp 181-185, issn 0451-5994, 5 p.Article

An investigation on springback/negative springback phenomena using finite element method and experimental approachRAHMANI, B; ALINEJAD, G; BAKHSHI-JOOYBARI, M et al.Proceedings of the Institution of Mechanical Engineers. Part B. Journal of engineering manufacture. 2009, Vol 223, Num 7, pp 841-850, issn 0954-4054, 10 p.Article

Large deflection of elastoplastic beams with prescribed moving and rotating endsHUANG, X; YU, T. X; LU, G et al.Proceedings of the Institution of Mechanical Engineers. Part C, Journal of mechanical engineering science. 2003, Vol 217, Num 9, pp 1001-1013, issn 0954-4062, 13 p.Article

Spring-back and how to control itBLAISDELL, D.Wire industry. 1992, Vol 59, Num 7, pp 494-498, issn 0043-6011Article

Sheet springback prediction based on non-linear combined hardening rule and Barlat89's yielding functionZHANG DONGJUAN; CUI ZHENSHAN; RUAN XUEYU et al.Computational materials science. 2006, Vol 38, Num 2, pp 256-262, issn 0927-0256, 7 p.Article

Springback analysis and control in small radius air bendingELKINS, K. L; STURGES, R. H.Journal of manufacturing science and engineering. 1999, Vol 121, Num 4, pp 679-688, issn 1087-1357Article

Effects of semi-isostatic densification on anatomy and cell-shape recovery on soakingBLOMBERG, Jonas; PERSSON, Bengt; BEXELL, Ulf et al.Holzforschung. 2006, Vol 60, Num 3, pp 322-331, issn 0018-3830, 10 p.Article

Experimental studies and constitutive modelling of the hardening of aluminium alloy 7055 under creep age forming conditionsLIHUA ZHAN; JIANGUO LIN; DEAN, Trevor A et al.International journal of mechanical sciences. 2011, Vol 53, Num 8, pp 595-605, issn 0020-7403, 11 p.Article

Numerical assessment of springback for the deep drawing process by level set interpolation using shape manifoldsRAGHAVAN, Balaji; LE QUILLIEC, Guenhael; BREITKOPF, Piotr et al.International journal of material forming. 2014, Vol 7, Num 4, pp 487-501, issn 1960-6206, 15 p.Article

Influence of multi-step heat treatments in creep age forming of 7075 aluminum alloy: Optimization for springback, strength and exfoliation corrosionARABI JESHVAGHANI, R; ZOHDI, H; SHAHVERDI, H. R et al.Materials characterization. 2012, Vol 73, pp 8-15, issn 1044-5803, 8 p.Article

Simulation of springback : Through-thickness integrationWAGONER, R. H; LI, M.International journal of plasticity. 2007, Vol 23, Num 3, pp 345-360, issn 0749-6419, 16 p.Conference Paper

Springback properties of single- and poly-crystalline pure aluminum processed by severe plastic deformationSAKAI, Takashi; YOSHIDA, Keisuke; KOYAMA, Jun-Ichi et al.Keikinzoku. 2009, Vol 59, Num 4, pp 179-184, issn 0451-5994, 6 p.Article

Numerical simulation of deformation in multi-point sandwich formingZHANG, Q; DEAN, T. A; WANG, Z. R et al.International journal of machine tools & manufacture. 2006, Vol 46, Num 7-8, pp 699-707, issn 0890-6955, 9 p.Article

Unloading of powder compacts and their resulting tensile strengthMARTIN, C. L.Acta materialia. 2003, Vol 51, Num 15, pp 4589-4602, issn 1359-6454, 14 p.Article

Comparison of Material Models for Spring Back Prediction in an Automotive Panel Using Finite Element MethodXIONGQI PENG; SHAOQING SHI; KANGKANG HU et al.Journal of materials engineering and performance. 2013, Vol 22, Num 10, pp 2990-2996, issn 1059-9495, 7 p.Article

Prediction of bend allowance and springback in air bendingKIM, Hyunok; NARGUNDKAR, Ninad; ALTAN, Taylan et al.Journal of manufacturing science and engineering. 2007, Vol 129, Num 2, pp 342-351, issn 1087-1357, 10 p.Article

Material characterisation for reliable and efficient springback prediction in sheet metal formingKRASOVSKYY, Andriy; SCHMITT, Winfried; RIEDEL, Hermann et al.Steel research international. 2006, Vol 77, Num 9-10, pp 747-753, issn 1611-3683, 7 p.Article

Effect of the elasticity formulation in finite strain on springback predictionCHATTI, S.Computers & structures. 2010, Vol 88, Num 11-12, pp 796-805, issn 0045-7949, 10 p.Article

Simulation of three-roller bending process using ANN: a parametric studyGANDHI, A. H; GOHIL, P. P; RAVAL, H. K et al.International journal of manufacturing research (Print). 2009, Vol 4, Num 3, pp 265-280, issn 1750-0591, 16 p.Article

Study of the inelastic response of TRIP steels after plastic deformationPEREZ, R; BENITO, J. A; PRADO, J. M et al.ISIJ international. 2005, Vol 45, Num 12, pp 1925-1933, issn 0915-1559, 9 p.Article

Establishment of a 3D FE model for the bending of a titanium alloy tubeJIANG, Z. Q; YANG, H; ZHAN, M et al.International journal of mechanical sciences. 2010, Vol 52, Num 9, pp 1115-1124, issn 0020-7403, 10 p.Conference Paper